Author Topic: LT-95a fitting  (Read 315 times)

Offline mudmouse

  • Newbie
  • *
  • Posts: 36
  • THANKS 4
  • Location: Kariong
LT-95a fitting
« on: February 29, 2020, 04:59:47 PM »

Dear all.

I probably could name this subject 'not fitting'.... hence the questions..

I've removed the gearbox from the Perentie and replaced the clutch/oil pump gears and pump cover seal. When attempting to refit the gearbox I get to within 10mm or so of the bell housing seating on the engine and that's it. I've rotated the flywheel and noted the drive flange rotate - so that and the fact it's 10mm away surely means the input shaft is in the cutch plate. I've taken the box out a second time to check clutch plate alignment etc, but nothings obvious.

When replacing the input shaft spigot I fitted it just under flush with the spigot face - as was the one I removed.

Bearing in mind my workshop is a stone cobbled driveway, it's not only hot and annoying, but I'm expecting some resistance with the trolley jack and engine hoist when sliding them around, but even trying a scissor jack applying pressure to the rear of the box just pushes the engine forward - only tried this to test a theory.

Any advice would be appreciated.

Thank you,

Matt
Perentie GS 49-515
No.5 177-360

Offline mudmouse

  • Newbie
  • *
  • Posts: 36
  • THANKS 4
  • Location: Kariong
Re: LT-95a fitting
« Reply #1 on: February 29, 2020, 08:25:04 PM »


Dear all.

It's in.

I often reflect on the photo of diggers dragging a field gun up a muddy slope in PNG to put things in perspective.

Constant angle checking, adjustments, a bit of bad language and persistence seems to have done the job.

Matt.
Perentie GS 49-515
No.5 177-360

Offline BEARMAN

  • Hero Member
  • *****
  • Posts: 647
  • THANKS 99
  • Location: Hay Point
  • REMLR No: 430
Re: LT-95a fitting
« Reply #2 on: February 29, 2020, 08:30:44 PM »
Hope you got it in all the way by hand without pulling it in with the bolts.
09/1998 Perentie 6X6 ARN202516 - BRUTUS

Offline THE BOOGER

  • Administrator
  • Veteran
  • *****
  • Posts: 1501
  • THANKS 147
  • Location: wetherill park, sydney
  • REMLR No: 282
Re: LT-95a fitting
« Reply #3 on: February 29, 2020, 09:08:06 PM »
So standard Landy meching eh ;D
s111 GS, no 5, xt600 & Ferret mk2
Geoff C

Offline mudmouse

  • Newbie
  • *
  • Posts: 36
  • THANKS 4
  • Location: Kariong
Re: LT-95a fitting
« Reply #4 on: February 29, 2020, 09:37:45 PM »
Hope you got it in all the way by hand without pulling it in with the bolts.

Hi Brian,

Yes I read about bending the tabs and in any case, forcing splines rarely works out.

Matt
 
Perentie GS 49-515
No.5 177-360

Offline mudmouse

  • Newbie
  • *
  • Posts: 36
  • THANKS 4
  • Location: Kariong
Re: LT-95a fitting
« Reply #5 on: February 29, 2020, 09:38:40 PM »
So standard Landy meching eh ;D

Just without the striped apron

:)
Perentie GS 49-515
No.5 177-360