Author Topic: edic motor  (Read 219 times)

Online tona

  • Full Member
  • ***
  • Posts: 178
  • THANKS 10
  • Location: stirling 6021
  • REMLR No: 463
edic motor
« on: August 04, 2018, 05:24:17 PM »
 >:(   COULD some one out there give me a complete circuit for the edit motor on a rfsv please,thanks ,TONA,.  B,,,,, thing is starting to play up, may be time to remove it completely?,TONA.

Offline dugite

  • REMLR Committee
  • Hero Member
  • ***
  • Posts: 986
  • THANKS 87
  • Location: Tamworth
  • REMLR No: 374
Re: edic motor
« Reply #1 on: August 05, 2018, 09:18:26 AM »
If compliance is an issue, removal and replacement with a pull stop would not be approved over here on annual rego inspection (just posted also re the D1 rims).

But it may get past an uneducated inspector - they can only tell you to refit it :)

If no one else posts the wiring today I'll look up a copy when I get back and post it.
2a 109 114-341,
No.5 173-589,
W/S Platform 178-000,
PT1 204-796

Offline Carzee

  • REMLR Committee
  • Veteran
  • ***
  • Posts: 3090
  • THANKS 130
  • Perentie FFR 50-257
    • RC's Shed
  • Location: Canberra
  • REMLR No: 007
Re: edic motor
« Reply #2 on: August 05, 2018, 12:11:43 PM »
I had an attempt, my 2c worth.

Offline Dopey

  • Newbie
  • *
  • Posts: 13
  • THANKS 9
  • Location: Sydney, NSW.
Re: edic motor
« Reply #3 on: August 05, 2018, 01:51:28 PM »
These motors can and do get a fair bit of rust in them, this is a mates one that I'm currently taking apart and rebuilding for him.

Offline Dopey

  • Newbie
  • *
  • Posts: 13
  • THANKS 9
  • Location: Sydney, NSW.
Re: edic motor
« Reply #4 on: August 05, 2018, 01:55:31 PM »
Also, the same edic motor is available to buy, but in a 24volt version.
It uses a slightly different cable, but you take it off and use the standard Perentie one.
The 12 volt versions are (as far as I'm aware) unavailable at the moment.

https://www.alibaba.com/product-detail/Engine-Diesel-shutoff-Stop-Solenoid-12V_60433669470.html

Part numbers for the 24volt one are Jideco MK294 & 5-81900-008-01.

The motors are very similar to the ones found in some Disco sunroof mechanisms & some electric window winders & smaller windscreen wipers.
« Last Edit: August 05, 2018, 01:58:36 PM by Dopey »

Online tona

  • Full Member
  • ***
  • Posts: 178
  • THANKS 10
  • Location: stirling 6021
  • REMLR No: 463
Re: edic motor
« Reply #5 on: August 05, 2018, 04:23:34 PM »
   THANKS  GUYS ,I may attempt to remove it tomorrow if the weather is a bit better over here,I am leaning toward a cable set up thats for sure,TONA.

Offline Philthy

  • Sr. Member
  • ****
  • Posts: 499
  • THANKS 68
  • Location: Brisbane
  • REMLR No: 425
Re: edic motor
« Reply #6 on: August 06, 2018, 07:54:09 PM »
>:(   COULD some one out there give me a complete circuit for the edit motor on a rfsv please,thanks ,TONA,.  B,,,,, thing is starting to play up, may be time to remove it completely?,TONA.

https://www.aulro.com/afvb/technical-chatter/160184-wiring-edic-motor-relay-2.html

Easy to recondition. Internal rust shorting inside. Sometimes it will work after a some firm taps with a hammer to dislodge the shorting crud. Mine had a short from sitting around. Dismantled it cleaned it, treated and sealed metal surfaces with motor varnish. All good. Good luck. Don't forget to bench test it as you assemble it. 

Online tona

  • Full Member
  • ***
  • Posts: 178
  • THANKS 10
  • Location: stirling 6021
  • REMLR No: 463
Re: edic motor
« Reply #7 on: August 07, 2018, 07:31:12 PM »
 :(   THANKS for the info guys I will attempt to remove it tomorrow , if its buggered its going to get the cable mod,TONA.

Online tona

  • Full Member
  • ***
  • Posts: 178
  • THANKS 10
  • Location: stirling 6021
  • REMLR No: 463
Re: edic motor
« Reply #8 on: August 10, 2018, 06:17:43 PM »
 ;)   HELLO fellow members, started to pull edic checked it out to make sure it was faulty guess what no power going in to it  checked power coming out of immobiliser no power coming out , thats it remove immobiliser  completely ,re connect wires to sign switch turn on sign switch edic motor goes on and off, reassemble the whole thing and have had no trouble since so far, we wills hong this lot lasts , thanks for everybody's assistance and pics and things ,cheers for now ,TONA 51 590.

Offline Philthy

  • Sr. Member
  • ****
  • Posts: 499
  • THANKS 68
  • Location: Brisbane
  • REMLR No: 425
Re: edic motor
« Reply #9 on: August 10, 2018, 06:24:34 PM »
Great a easy fix!