Author Topic: 109 S2A LRPV Help  (Read 1378 times)

Offline JR1

  • Newbie
  • *
  • Posts: 3
  • THANKS 0
  • Location: Murrumbateman
109 S2A LRPV Help
« on: December 12, 2017, 09:28:27 AM »
G'day Folks,
I am after a bit of help in identifying a friends Land Rover.
It looks like a series 2a 109 ex LRPV (SAS/Norforce??), Vietnam era, infantry or RAEME with a few home mods. The white ghost on the drivers side front fender are interesting as is the wire cutter on the bull bar and the re-purposed tailshaft gun mount in the rear.  The circular yellow plate with the figure 3 on the front I think from memory is a bridge load marker (3 tons?) but the Xmas Tree colors and numbers have me stumped.
Perhaps this vehicle was previously known to this site?
Any assistance would be most appreciated.

cheers
Jeff
 

Offline Ravvin

  • REMLR Inc
  • Hero Member
  • *
  • Posts: 530
  • THANKS 60
  • Location: Wesley Vale, Tasmania
  • REMLR No: 432
Re: 109 S2A LRPV Help
« Reply #1 on: December 12, 2017, 10:49:16 AM »
Hi and welcome to the forum.

Just looking through the Library info on the www.remlr.com site and it looks like your Xmas tree is for 6 RAR.
I remember seeing Casper mentioned somewhere on either this forum or the old one on the AULRO site, but can't remember exactly where.
If you can get the VIN or a pic of the plate on the front dash with the census details and other info, someone should be able to work out it's ARN and maybe give you some better info.

Greg.

Offline FFRMAN

  • REMLR Committee
  • Veteran
  • ***
  • Posts: 2797
  • THANKS 207
  • Location: Western Vic.
  • REMLR No: 314
Re: 109 S2A LRPV Help
« Reply #2 on: December 12, 2017, 12:38:42 PM »
I recon this one did the rounds a few years ago. Was identified as a 2A ffr and been mocked up to look "special".
Lots...............
VMVC 251,

Offline JR1

  • Newbie
  • *
  • Posts: 3
  • THANKS 0
  • Location: Murrumbateman
Re: 109 S2A LRPV Help
« Reply #3 on: December 12, 2017, 01:17:05 PM »
Thanks guys, I will see if I can get a pic of the id plate.

Offline Mick

  • Veteran
  • ******
  • Posts: 1156
  • THANKS 156
  • Location: Melbourne
Re: 109 S2A LRPV Help
« Reply #4 on: December 12, 2017, 01:21:12 PM »
Hi JR ,

I think FFRMAN is right , having said that the roll bar does look like a LRPV Mk 2 job and the water  cans on the sides was a very early LRPV mod.

If I was to bet on her , I'd say a mock up job.

Cheers,

Mick

Offline mike_k

  • Sr. Member
  • ****
  • Posts: 427
  • THANKS 49
  • Location: Victoria
  • REMLR No: 20
Re: 109 S2A LRPV Help
« Reply #5 on: December 12, 2017, 05:00:51 PM »
Iím definetely not a LRPV expert, but history always shows -


 that if there is a small vice on the brushbar, its a definite fake...... ;)

Offline JR1

  • Newbie
  • *
  • Posts: 3
  • THANKS 0
  • Location: Murrumbateman
Re: 109 S2A LRPV Help
« Reply #6 on: December 13, 2017, 09:57:54 AM »
Thanks guys, yes the vice was definitely aftermarket but being an ex Norforce member we used to stick all sorts of crap on our Toyota's to make life out bush easier. These vehicles became a very personalized item when in service. Mine for example had pepperoni hooks and a fire extinguisher bracket bolted to the engine to heat tins of baked beans on the go.
The ARN number is 113-638 and chassis 25307369B. Its actually stamped as R.RECN.LRPV on the plate. 

cheers
Jeff

Offline workshop

  • Newbie
  • *
  • Posts: 29
  • THANKS 4
  • Location: lake macquarie
  • REMLR No: 39
Re: 109 S2A LRPV Help
« Reply #7 on: December 17, 2017, 02:04:12 PM »
haven't seen this for a while its a copy of one built by a bloke in Sydney some time ago
1961 112 166 workshop truck
1964 101 410 workshop trailer
1969 175 252 fft radio truck