Author Topic: Series 2A lubrication  (Read 9622 times)

Will

  • Guest
Series 2A lubrication
« on: September 25, 2012, 08:24:09 AM »
Gday, just about to refresh the engine, gear box, transfer case and diff oils. The workshop manual states that the gear box, transfer case and diff oil is the same. The only problem is that i cant find the types of oils / fluids stated. The most recent information on current oils is all for series 3 models.

Any recomendations on the right types of good quality oils would be greatly appreciated.

Thanks!

Offline Phoenix

  • Administrator
  • Veteran
  • *****
  • Posts: 2164
  • THANKS 85
    • REMLR
  • Location: Launceston, Tasmania
  • REMLR No: 129
Re: Series 2A lubrication
« Reply #1 on: September 25, 2012, 08:41:34 AM »
EP 90 everywhere is the go!

Manual gear oil 80/90 is what it is often what it is advertised as.  I use penrite myself.  http://www.penriteoil.com.au/products/manual-gear-&-differential-oils/gear_oil_80w-90_%28new%29
REMLR Webmaster
Eden - 1961 Series 2 Ambulance, 108-098

Offline Phoenix

  • Administrator
  • Veteran
  • *****
  • Posts: 2164
  • THANKS 85
    • REMLR
  • Location: Launceston, Tasmania
  • REMLR No: 129
Re: Series 2A lubrication
« Reply #2 on: September 25, 2012, 08:42:44 AM »
this page of REMLR should be of some help

http://www.remlr.com/sheds/khshedparts.html

REMLR Webmaster
Eden - 1961 Series 2 Ambulance, 108-098

Will

  • Guest
Re: Series 2A lubrication
« Reply #3 on: September 25, 2012, 08:50:29 AM »
Thanks very much for the prompt reply!

The military service records are fantastic.

Looks like it is time to greasy........

Offline bronzie66610

  • REMLR Inc
  • Full Member
  • *
  • Posts: 208
  • THANKS 20
  • Location: Port Franklin Vic.
  • REMLR No: 373
Re: Series 2A lubrication
« Reply #4 on: September 26, 2012, 07:48:51 PM »
Hi
Have a series 2A operators book spare. Can post to you if you would like it.
David
1 Series 2a (Civ)
1966 S2A GS ARN 113-990
1964 S2A GS ARN 112-951
1964 S2A GS ARN 112-915

Offline Uncle Ho

  • REMLR Inc
  • Sr. Member
  • *
  • Posts: 305
  • THANKS 54
  • Location: Godwin Beach Qld.
  • REMLR No: 003
Re: Series 2A lubrication
« Reply #5 on: September 27, 2012, 11:19:45 AM »

I would recommend Castrol EPX80/90 for all of the following,Gearbox,Transfer case,Front Diff,Rear Diff,Swivel Hubs,and Steering Box.also the Relay Box (it is difficult to fill,remove 2 opposite small screws,and dribble some into it,I use a thin piece of wire so the oil runs down it)it takes about 250ml from memory,DO NOT FILL WITH GREASE. nor do you fill the swivel hubs with grease or 1 shot,as they are Universal joints and need to run in oil,unlike the later CV joints which are designed to run in molybdenum type grease like 1 shot  :)

Will

  • Guest
Re: Series 2A lubrication
« Reply #6 on: September 27, 2012, 01:55:11 PM »
Thanks for the information. I replaced the oil in both diffs, the gear box and tranfer case last night. All seemingly went well. Was going to do the engine oil but decided to wait until i have the time to do the sump gasket as it is leaking in about 4 places! 

Had trouble finding the fill points on the gear box and tranfer case. It seems there is bypass hose linking the two together? I took the hose off, filled it up to that level on both the transfer and gear box and put the hose back on. I am hoping this is the right thing to do. Next will be steering box, swivel hubs, relay box and cv's.

I reckon the tail shaft need a good bit of grease too  :)

Will

  • Guest
Re: Series 2A lubrication
« Reply #7 on: September 27, 2012, 01:57:33 PM »
Hi
Have a series 2A operators book spare. Can post to you if you would like it.
David

Thanks David, very kind of you to offer. I have just sourced and been using the 2 & 2A original workshop manual. It seems to cover all aspects in detail. What is the operators book like? Would it be a usefull addition, and how much were you looking to get for it? Regards,Will

Offline Phoenix

  • Administrator
  • Veteran
  • *****
  • Posts: 2164
  • THANKS 85
    • REMLR
  • Location: Launceston, Tasmania
  • REMLR No: 129
Re: Series 2A lubrication
« Reply #8 on: September 27, 2012, 03:18:15 PM »
It's not that uncommon for the 2 to be linked in civy life to transfer any leaking fluids fron one to the other as one tends to leak into the other and overflow.
REMLR Webmaster
Eden - 1961 Series 2 Ambulance, 108-098

Offline bronzie66610

  • REMLR Inc
  • Full Member
  • *
  • Posts: 208
  • THANKS 20
  • Location: Port Franklin Vic.
  • REMLR No: 373
Re: Series 2A lubrication/Operators book
« Reply #9 on: September 27, 2012, 05:05:10 PM »
WILL,   PM  me and I shall post them to you free of charge.

Regards
David
1 Series 2a (Civ)
1966 S2A GS ARN 113-990
1964 S2A GS ARN 112-951
1964 S2A GS ARN 112-915

Offline Uncle Ho

  • REMLR Inc
  • Sr. Member
  • *
  • Posts: 305
  • THANKS 54
  • Location: Godwin Beach Qld.
  • REMLR No: 003
Re: Series 2A lubrication
« Reply #10 on: September 27, 2012, 07:46:56 PM »


G'day Folks  :)

This is /was a common thing with Jeeps during WW11, it is caused by the gearbox output bearing to the tranfer case spinning in it's housing and therefore wearing the housing hole oversize,hense the oil passes from G/box to transfer,but it can do the reverse,transfer to G/box,(mine does) but was used post service by owners,the later S3 army fix was to peg it,by machining a slot in the casing,and drilling and fitting a peg to the bearing,not often seen on GS type vehicles but can be found on specialist vehicles,Bloodboxes,W/shop's Etc.

cheers

Offline bronzie66610

  • REMLR Inc
  • Full Member
  • *
  • Posts: 208
  • THANKS 20
  • Location: Port Franklin Vic.
  • REMLR No: 373
Re: Series 2A lubrication
« Reply #11 on: September 27, 2012, 07:56:33 PM »
I had same problem in a S3. They replaced with a double lipped seal under warranty and no probs after that.
1 Series 2a (Civ)
1966 S2A GS ARN 113-990
1964 S2A GS ARN 112-951
1964 S2A GS ARN 112-915

Offline boxy

  • REMLR Committee
  • Sr. Member
  • ***
  • Posts: 369
  • THANKS 50
  • Location: Grattai,NSW
  • REMLR No: 422
Re: Series 2A lubrication
« Reply #12 on: January 11, 2017, 11:29:47 AM »
The Majority of the advice here is to run EP 90 everywhere.

The Lube Chart says OEP 220 for the Gearbox and Transfer case which is EP90 and says OEP600 for the diffs which is 85w 140

Should i be getting the two different oils for my 2A?
RFSV (Upgrade) 51-670
S2A 88 GS Fitted for Stretcher 113-731
RAAF Aluminium Trailer
Haulmark PT2-2 204-550 Haulmark PT1-1.2 204-831

Offline mike_k

  • Sr. Member
  • ****
  • Posts: 439
  • THANKS 49
  • Location: Victoria
  • REMLR No: 20
Re: Series 2A lubrication
« Reply #13 on: January 11, 2017, 11:58:34 AM »
Boxy,

I've always just used EP 90 in everything on the 2A, and its been fine.
That is what the civvy manuals recommend as well, no fancy 80-140 around in those days I guess!

Using the same oil for everything is a bit simpler as well, I usually get in in a 20 litre drum.

How is the 2A coming along?

Cheers,

Mike.


Offline Mick

  • Veteran
  • ******
  • Posts: 1167
  • THANKS 157
  • Location: Melbourne
Re: Series 2A lubrication
« Reply #14 on: January 11, 2017, 01:02:11 PM »
Hi Boys,

From memory wasn't OMD110 engine oil and 220 in the gear box , etc ?

Whatever that equates to Today ?

Good luck Boxy 👍
Cheers,

Mick